0

How To Remove the iPhone Battery

Posted by Arch on March 28, 2019
How to Remove the iPhone Battery

Not all iPhone batteries can be removed in the same way. The process is very similar, but you’ll have to use different tools depending on the model. Also, note that different models will have slightly different component arrangements.

Check out how to remove the battery from the iPhone 7 and above, as well as the slightly older iPhone 6 series smartphones to get an idea of how things may differ from one model to another. If you learn how to remove it from one iPhone, you will likely know how to handle a newer version too.

Remove the iPhone Battery

Removing the Battery: iPhone 7 and Newer

Removing a battery from an iPhone may not be an easy task. It is doable at home with the right tools and steady hands, but there is still a risk of damaging your phone. Removing the battery will void your warranty, so it’s always best to have it done at a licensed Apple Store.

If you opt to do this at home, you’ll need the following tools:

  1. Suction cup
  2. Spudger
  3. Pentalobe P2 screwdriver
    pentalobe screwdriver
  4. 2mm screwdriver
  5. 6mm screwdriver
  6. 3mm screwdriver
  7. 1mm screwdriver
  8. 1mm screwdriver
  9. 9mm screwdriver

Although the list of tools seems scary, the process itself isn’t if you approach it with caution. You should turn off your iPhone first and then warm up the bottom section of the case. Fix the suction cup to the screen and gently try to lift the bottom of the screen while using a spudger to pry it open.

 

Be careful not to force it as you might damage the wiring. Once you manage to remove all the adhesive, turn the screen to the right as you would open a book. From there, follow these steps:

  1. Remove the four tri-point screws from the lower bracket display (look for a connecting ribbon)
  2. Take out the display bracket
  3. Remove the battery connector (the perpendicular plastic strip)
  4. Detach the other plastic strip and the gray strip underneath it
  5. Unscrew the smaller tri-point screws holding the bracket over the second display ribbon
  6. Remove the bracket
  7. Remove the black plastic strip (the other connector)
  8. Pry up the connector with the spudger and remove it
  9. Remove screws from the barometric vent (black bracket in the bottom-left corner)
  10. Remove the barometric vent to uncover the Taptic Engine connector
  11. Pry up the black plastic connector and remove it
  12. Remove the screws and remove the Taptic Engine from the case
  13. Peel back adhesive strips covering the battery (you may need to warm up the adhesive)
  14. Remove the battery

Remember to be very careful while doing this. Everything from lifting connectors to peeling strips should be done slowly. When removing the three strips holding the battery, you shouldn’t risk tearing or wrinkling. Go slow and try warming up the adhesive if you feel too much feedback.

Removing the Battery: iPhone 6 Series

The iPhone 6, 6 Plus, 6S, and 6S Plus will require different screwdrivers. Have Pentalobe P2 screwdrivers on hand with 3.6mm heads for the iPhone 6 and 6 Plus and 3.4mm heads for the 6S and 6S Plus phones.

You’ll also need a suction cup and a spudger to lift the screen and deal with other small components.

Here’s what you should do:

  1. Turn off your iPhone and remove the screws next to the lightning port
  2. Use the suction cup on the lower-left corner of the screen
  3. Lift the screen while holding down the case
  4. Pry open the case with the spudger and lift the display to a 90-degree angle
  5. Look for the battery connector bracket (it’s covered by a rectangular metal piece with two screws)
  6. Use a #000 Philips screwdriver to take out the screws
  7. Pry up the connector off the logic board
  8. Remove the cable bracket by removing the screws first (five screws on the iPhone 6, 6 Plus, and 6S Plus, and four screws on the iPhone 6S)
  9. Disconnect the camera cable (a large connector with a cable that leads to the display)
  10. Remove remaining connectors
  11. Separate the screen from the rest of the case
  12. Peel off the adhesive strips from the bottom of the battery
  13. Pry out the battery

suction cup

Words of Caution

As you can see, whether you have an older iPhone or a new one, the process of removing the battery is very similar. You may need different tools to handle the various screws and connectors, but a few general guidelines always apply.

Never force-pull the screen because you may risk breaking the case, the cables, or connectors, which may render your iPhone useless. If the adhesive presents a problem, use a hair drier from a distance to warm it up.

Always separate all connectors between the display and the screen to separate the case. Uncover the battery by unscrewing the connectors and brackets on top of it. Use a manual to find out exactly where the battery is on your iPhone model.

Go as slow as you can in each step, especially when prying up connectors and removing the battery. Damaging the battery could release hazardous chemicals, not to mention damaging your phone. Remember, if you need your battery removed or changed, it is always best to take your phone to an Apple Store or mail it to an Apple Repair Center.

Leave a Reply

Your email address will not be published. Required fields are marked *


Disclaimer: Some pages on this site may include an affiliate link. This does not effect our editorial in any way.